Stamping Mould
ADD：
Houyang Mould City, West-city, Huangyan, Zhejiang　
E-mail：
kedamould@mail.tzptt.zj.cn
TEL：
0086-576-84025886 13806572035 13857635888
FAX：
0086-576-84025780 84025781
KD812-820 Series Fully Automatic Bottle-blowing Machine
一、 The process of making bottles
1. The preforms will be automatically transmitted to the place where they will be put in order automatically on the preform sideway.
2. The heating-heads gain the preforms in succession at the entrance and the correspondence system will control the prefoms to get the accurate temperature when they are heated by infrared ray,meanwhile,the temperature in difierent level is showing clearly on the touch-screen.
3. The protruding wheel will control the mould frame to open and close compeletely,to change the speed of locking mould,meanwhile,the bottle-blowing parameters for every moud cavities will be controlled and showed on the screen.(The control system adopts the advanced technology from Japan and Germany).
4. After the formation of the bottles,the machinery hand will automatically take them out from the moulds,automatically check and get rid of the defective goods.The bottles will be layed down from the band carrier the defective goods.
二、 Function and advantage
1. Automatically put and arragne the preforms in good order,the whole process is steady and reliable,the preforms are offered from the storage of the hopper automatically,and the heating system is perfect,the temperature for every section of the preform can be regulated freely.
2. Infrared oven ventilation cooling system,service life of the machine is long,with very high effenciency of the heating oven.
3. Infrared oven checks the temperature automatically after preforms are heated,to ensure the unaninous temperature,to avoid the defective products.
三、 Automatically taking and putting the preforms,taking out and putting the bottles in good order.
四、 The checking system can examine the defective bottles carefully.
五、 Changing moulds quickly,highly automatic,little bottle pollution.
S/N
Item
Unit
KD808
KD810
KD812
1
Mould cavities
Cavity
8
10
12
2
Working pressure
 Mpa
7-8
7-8
7-8
3
≤
Air blowing pressure
 Mpa
40
40
40
4
Height of bottle
mm
330
330
330
5
stroke of opening mould
mm
130
30
130
6
Thinkness of mould
mm
Φ190
Φ190
Φ190
7
Heat unit group
Group
6
10
10
8
Heated-light layer
Layer
9
9
9
9
Max heat power
Kw
50
80
80
10
Voltage
v
380
380
380
11
Frenquency
Hz
50/60
50/60
50/60
12
Preform lengh
mm
≤180
≤180
≤180
13
bottle neck diameter
mm
Φ20-Φ28
Φ20-Φ28
Φ20-Φ28
14
bottle diameter range
mm
Φ20-Φ105
Φ20-Φ105
Φ20-Φ105
15
Preform raw material
Kg
PET
PET
PET
16 Volume range L 0.2-2 0.2-2 0.2-2
17 Capacity for mineral bottle Pcs/h 10000 12000 13500
18 Capacity for heat -resistant bottle Pcs/h 6800 8000 9000
19 Weight Kg ≤8000 15000-17000 15000-17000
20 Dimension of main machine mm 3500×2500×1900 3400×2600×2600 3400x2600×3300
21 Dimension of heater mm   5600×1005×2600 5600×1005×2600
22 Preform-tidied machine size mm   4000×5400×3500 4000×5400×3500
23 Dimension of electrical box mm   2400x2100x700 2400x2100x700